Litter robot 3 cycling light flashing

Dec 3, 2021 · The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter. It is subjected to conditions which most robots - if they had a choice, would prefer not to be subjected to.

Litter robot 3 cycling light flashing. Better understand your Litter-Robot 3's buttons and lights. Learn more about the programming button functions with our easy-to-follow guide. ... The robot will begin a clean cycle when power is turned on. Press and hold, while at the home position, to enter night light setting mode. ... Blue, Yellow, Red Flashing Sequentially: Cannot find Dump ...

My litter robot was doing well, but now it start to cycling and it stopped, the yellow light is flashing. ... Litter Robot 3 OA Yellow Light Flashing (Pinch Detector Problem) Stuck on Yellow. Litter robot cycle light flashing. h60hadgi May 6, …

clean the metal tabs (bonnet and base) bend the plastic tabs outward. put plastic tape after connecting the bonnet to the base so it’s “well connected”. move the LR3 away from walls. disable night light. After all applied, it seems working. Sharing just in case you find the short-circuit trick itself does not work. 3.If your robot has problems with the yellow blinking light, please follow the troubleshooting below to determine whether the issue is due to excess weight, the bonnet connection, or the Anti-Pinch safety feature: *The blinking yellow light will switch to blinking red after 2 minutes if the cat sensor (CATS) has been continuously activated by exce...Related: Litter-robot vs. Catlink full comparison. Another thing to note is that you should never place your Litter-Robot on an uneven surface. The Base must be on a flat surface and should not be leaning to either side. 4. Check the Lights. Your Litter-Robot’s lights are very useful in telling you what the problem might be. Make it a habit ...Try disconnecting the app, installing and run it. The app Itself may be the problem. 1. DisciplineAgile7187 • 1 yr. ago. It may be a seal issue. I was sending back my second LR4 and trying to clean it. It had a small bucket full of litter in the actual moving globe underneath. So frustrated. Bought the LR3 connect. Dec 9, 2018 · If your robot has problems with the yellow blinking light, please follow the troubleshooting below to determine whether the issue is due to excess weight, the bonnet connection, or the Anti-Pinch safety feature: *The blinking yellow light will switch to blinking red after 2 minutes if the cat sensor (CATS) has been continuously activated by exce... Sometimes this problem is caused by a faulty power supply or the motor itself. If even after checking the set screw on the motor and checking the voltage on the power supply with …Feb 11, 2023 · Why is Litter-Robot Stuck on Cycling Light? If you see a solid yellow light on the control panel, that means it is cycling (it can also mean it’s paused). Litter-Robot Cycle Light Flashing. There’re 2 types of flashing. If you see a yellow light that’s flashing slowly, it means your robot’s cycle was interrupted.

If the unit cycles and the light turns solid blue, then your Litter-Robot is cycling normally.We recommend cycling the unit 1-2 more times to confirm. If the unit does not return to a solid blue light and you have a single-board style drawer full indicator, then go to the bottom of this email and try Recalibrating the sensor.Oct 18, 2016 · Step 10: Manual Cat Sensor Activation. Press on the Globe just above the entrance in a forward and downward direction—just press and release. The blue light should turn off and the red light should come on. You've activated the Cat Sensor to simulate your cat entering the Globe, then exiting. Allow the Wait Time (3, 7, or 15 minutes ... Try disconnecting the app, installing and run it. The app Itself may be the problem. 1. DisciplineAgile7187 • 1 yr. ago. It may be a seal issue. I was sending back my second LR4 and trying to clean it. It had a small bucket full of litter in the actual moving globe underneath. So frustrated. Bought the LR3 connect. Watch on Litter-Robot 3 is equipped with infrared emitters and sensors located above the Waste Drawer that check if the drawer is full each time the Globe returns to the Home …Unplug your Litter-Robot for 10 seconds and then plug it back in. This performs a hard reset. When your unit is powered back on, it will perform a Clean cycle. Once the Clean cycle is complete, the unit should go back to blue ready status. If your unit returned Home and displays a solid blue light, you've been successful. Unplug your Litter-Robot for 10 seconds and then plug it back in. This performs a hard reset. When your unit is powered back on, it will perform a Clean cycle. Once the Clean cycle is complete, the unit should go back to blue ready status. If your unit returned Home and displays a solid blue light, you've been successful.

If your Litter-Robot 3 is displaying a yellow light flashing quickly, this indicates a cycle has been interrupted by the Anti-Pinch Safety Feature and you will need to inspect the pinch sensor. Inspect the Sensors The purpose of the pinch sensor is to detect if an object is blocking the waste port during the Globe rotation. The shield is a possible cause for the 3 lights flashing fault. We strongly recommend removing the Internal Shield. To remove the shield, you will need a Phillips head screwdriver. Remove the screw from the center of the black Key on the back of the Globe. Once the Key is removed, you can easily pull the shield out from the entrance of the Globe.Feb 11, 2023 · Why is Litter-Robot Stuck on Cycling Light? If you see a solid yellow light on the control panel, that means it is cycling (it can also mean it’s paused). Litter-Robot Cycle Light Flashing. There’re 2 types of flashing. If you see a yellow light that’s flashing slowly, it means your robot’s cycle was interrupted. Op, I am currently in the yellow blinking hell. New bonnet, cleaning every metal connection, taking apart and cleaning the cat sensor (legit the dumbest design for a spring connection), saging, meditating, calling it bad names, and even just manually Turing the globe. MNPistagnesi December 3, 2021, 12:00am 1. The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter. It is subjected to conditions which most robots - if they had a choice, would prefer not to be subjected to.

Lpn part time jobs near me.

A solid yellow light on your Litter-Robot 3 control panel indicates that the unit is cycling or paused, and requires no action from you. However, a flashing yellow light could mean one of two things. Flashing yellow slowly Flashing slowly (about once per second) means the Litter-Robot clean cycle was interrupted.That Blue flash followed by the rapid Yellow flash is indicative of a failure in the Drawer Full Indicators and Pinch Detect Terminals. If your Litter-Robot is in Warranty, give our Customer Experience Specialists a call at 877.250.7729.Red foxes mature sexually and produce a litter at about 1 year of age. Pups are blind and helpless at birth and remain with parents for roughly half a year. Red foxes typically pair monogamously.WiFi Flashing Yellow Robot cycling *Yellow light moving with the rotation of the globe Round Robin Yellow* No action required or press Reset to cancel timing ... 3 2 4 If possible, place the Litter-Robot in the same location as the old litter box (at least during transition).The following troubleshooting should resolve the blue light blinking while the waste drawer is empty. Once resolved, the unit should consistently recognize when your cat visits and cycle accordingly. To troubleshoot the blue blinking: Remove the drawer from the unit and press RESET. If the unit goes to solid blue, press the CYCLE button. The unit …Sometimes this problem is caused by a faulty power supply or the motor itself. If even after checking the set screw on the motor and checking the voltage on the power supply with …

Power TheDevice “On”. If your device doesn’t cycle automatically, Press “Cycle.”. If it cycles and the light turns blue. Be sure your device is running normally. But be confirmed at least after two to three cycles. If it is still not working properly, Try Recalibrating the sensors. It may work on the issue.If they are fast flashing they're the pinch sensor, but there are other errors which can cause flashing yellow lights. Step 1 is making sure that it isn't touching anything, like the wall - if you've already taken the darn thing apart you probably already did that though. Step 2 is something we do regularly with our robot because this used to ... Litter Robot 3 Cycling Issues… For some reason, the past four days my litter robot has been having on and off issues with litter cycling. It no longer cycles on its own and I’m now manually having to press cycle every few hours, and about every other cycle it will stop halfway through the cycle for anywhere between a couple seconds and a ... Sometimes this problem is caused by a faulty power supply or the motor itself. If even after checking the set screw on the motor and checking the voltage on the power supply with …This is screaming possible control board issues, At first I was thinking the weight sensor was either too sensitive and or drifting out of spec but if its getting stuck randomly it could be a sensor interface issue on the control board. Plus if your LR is going in to sleep mode consistently by its self and the night light is stuck on despite ...What do the lights mean? Yellow & Red Flashing Sequentially: Motor detects obstruction or jam Blue, Yellow, Red Flashing Sequentially: Cannot find Dump position Red, Yellow, Blue Flashing Sequentially: Cannot find Home position Need technical support? Our Troubleshooting Wizard will solve most issues and is the fastest way to get help.To troubleshoot the blue blinking, let’s start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base. 2.) Wait 10 seconds then plug the unit back in. 3.) Allow the unit to complete a start‐up cycle.I bought the original Litter robot about 6 years ago and it was life changing. I upgraded to the connect 3 about 4 years ago and it's been great up until this year. I was about to purchase a second unit (i have 3 cats,) but given this issue I'm tempted to try another globe-based option.

Litter-Robot Connect units only – look for the WiFi symbol on the control panel. Download the Whisker app and follow the onboarding instructions. Ensure proper placement Power on Add litter Download the app 1 3 2 4 If possible, place the Litter-Robot in the same location as the old litter box (at least during transition).

The gestation period for rabbits is 29-35 days with 1-12 babies per litter; birthing can occur in as little as 10 minutes per litter. The short birthing cycle means a female rabbit can give birth to a new litter before she is finished weani...So I took it apart cleaned it and put it all back together. Now all it will do is flash the blue light! The drawer is empty, the bag is not in the way, and it will not cycle at all, even when unplugged and plugged back in. Troubleshooting said to wipe the sensor with a qtip, so I wiped down the area, although I don't really see a black spot ...Disconnect the bonnet. Gently flex the two front bonnet tabs outward and hold for about 20-30 seconds. Reattach the bonnet. There are four tabs total: two in the back, two on the sides. You should feel a secure snap and hear a “click” when placed back into the slot, and the bonnet should sit closer to the base.If your litter robot 3 is not able to complete a cycle and is flashing yellow randomly, then watch this video for the fix!Our litter robot was giving us nigh...Cycling London To Istanbul The Long Way. 15000 Bicycle Touring with Hels on wheels. Itinerary, map, GPX track, advice. Bikepacking the world on 70USD/week.Litter-Robot by Whisker November 14, 2016 · If you've been troubleshooting issues with your Litter-Robot Open Air to no avail, try this Fresh Restart to eliminate confounding conditions and identify the problem if there is one.Slow blue light --> fast yellow flashing light. I have a pretty old LR 3 (non-Connect, serial # 028957). I replaced the DFI and pinch detect terminals about 1.5-2 years ago and it's been working pretty well since then. A few days ago, the unit stopped cycling entirely. The blue DFI light started blinking even when the tray was empty, and after ...Quick question. I got a litter robot 2 for about 2 years. It stop working today. The “empty” and “cycle” bottoms doesn’t work but only reset bottom works and “ready” is flashing blue. If I push the “reset” bottom, “cycling” is flashing yellow in 4 times per sec. The problem didn’t solve after I cleaned up pinch pins.If your litter robot 3 is not able to complete a cycle and is flashing yellow randomly, then watch this video for the fix!Our litter robot was giving us nigh...Fill your Litter-Robot to the fill line with litter and then perform a hard reset on your unit. Here’s how to do a hard reset on your Litter-Robot 4: Press and hold the Reset and Power buttons for 3 seconds. The light bar will flash red then go through a sequence of red, blue and green lights then begin a cycle.

Pound to dollar western union.

Dirt bike themed cake.

The following troubleshooting should resolve the blue light blinking while the waste drawer is empty. Once resolved, the unit should consistently recognize when your cat visits and cycle accordingly. To troubleshoot the blue blinking: Remove the drawer from the unit and press RESET. If the unit goes to solid blue, press the CYCLE button. The unit …Reboot your router. Completely close the Litter-Robot app. While the unit is at the Home position with the solid blue light, unplug your unit from the BASE, not the wall. Wait 15 seconds, plug it back in, and allow it to cycle until the solid blue light comes on (“Ready” status). Open the app and follow the steps.Feb 11, 2023 · Why is Litter-Robot Stuck on Cycling Light? If you see a solid yellow light on the control panel, that means it is cycling (it can also mean it’s paused). Litter-Robot Cycle Light Flashing. There’re 2 types of flashing. If you see a yellow light that’s flashing slowly, it means your robot’s cycle was interrupted. Dec 9, 2018 · If your robot has problems with the yellow blinking light, please follow the troubleshooting below to determine whether the issue is due to excess weight, the bonnet connection, or the Anti-Pinch safety feature: *The blinking yellow light will switch to blinking red after 2 minutes if the cat sensor (CATS) has been continuously activated by exce... All three flashing simultaneously: This means the unit cannot find the Dump or Home position. Disassemble the Globe and flip the magnets at both the 1 o’clock and 5 o’clock position. Replace the Globe, making sure it is on straight and in its tracks. At the back of the Globe, turn the black Key into the Key Pocket.Why is Litter-Robot Stuck on Cycling Light? If you see a solid yellow light on the control panel, that means it is cycling (it can also mean it’s paused). Litter-Robot Cycle Light Flashing. There’re 2 types of flashing. If you see a yellow light that’s flashing slowly, it means your robot’s cycle was interrupted.When I turn on the Litter Robot 3 (non-connect), blue light is flashing, then I press Reset and fast yellow light is flashing. When I press Reset again, blue light is flashing and so on.. What I checked so far: - Anti Pinch Pins looks good and are touching each other. - DFI is clean and 4 IR LEDs are blinking once a second.Find solutions for your Litter-Robot 3's three lights flashing position sensors issue. Fix issues with your Connect Upgrade Kit today! ... Once you’ve checked the condition, location, and orientation of the Position Sensor, reassemble the robot and initiate a clean cycle to determine if the problem was resolved. Replace the Globe, making sure ... ….

Regarding issues with your Litter-Robot 3, you may also see the blue light blinking. Before troubleshooting, it’s advisable to: Unplug your power supply and then wait for 10 seconds. Plug the unit back in and allow it to complete its cleaning cycle. If the light is solid blue, everything has reverted to normal.Why is the cycling light on Litter-Robot . This is just a friendly reminder that your Litter-Robot 3 is either cycling or paused, and there’s no need for you to take any action. It’s important to clean your self-cleaning litter box regularly to keep it functioning properly. Turn off the unit and unplug it from the wall before you begin ...Litter Robot III solid yellow light problem. Hi, we are currently experiancing an issue with our litter robot. The cycle light stays on and the litter refuse to turn or do anything else. We already changed the motor and the control board but still the same issue. The unit is out of warranty. Thank you for pointing me what I could check next. 3.If your robot has problems with the yellow blinking light, please follow the troubleshooting below to determine whether the issue is due to excess weight, the bonnet connection, or the Anti-Pinch safety feature: *The blinking yellow light will switch to blinking red after 2 minutes if the cat sensor (CATS) has been continuously activated by excess weight.robotshopTech June 12, 2018, 3:52pm 1. If your robot has problems with the yellow blinking light, please follow the troubleshooting below to determine whether the issue is due to excess weight, the bonnet connection, or the Anti-Pinch safety feature: *The blinking yellow light will switch to blinking red after 2 minutes if the cat sensor (CATS ...If you have a Litter-Robot III Open Air 3 and it's stopped working with yellow blinking / flashing light and/or the globe does not rotate in normal operating cycle or spinning continuously counter clockwise in one direction, then this video might be for you.On the Litter-Robot 3 Connect itself, there’s an automatic night light and an indicator that’ll let you know when the waste drawer is full without checking the app. It also has an 8-hour sleep mode feature, so you don’t have to wake up to the Litter-Robot cycling in the middle of the night, and an option to lock all the buttons on the control panel …1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2.) Wait 10 seconds then plug the unit back in 3.) Allow the unit to complete a start‐up cycle. If the light is solid blue, the code has been successfully cleared. If the light is still blinking, let’s proceed with troubleshooting.If the Litter-Robot 3 cannot find Dump and/or Home position, the control panel will display 3 lights blinking. If you have recently disassembled your globe, please advise.20 Dec 2018 What is blue light inside Litter-Robot?Hello, I have the litter robot 3, I’ve had it since maybe September and haven’t had many issues with it (other than it getting stuck mid cycle Sometimes but it fixes itself once I hit reset). Two days ago I got the flashing lights of death; the anti pinch sensor. Litter robot 3 cycling light flashing, During each Clean cycle, the DFI Sensor will measure the level of waste within the Waste Drawer as the Waste Port passes over the Waste Drawer. Once a full Waste Drawer is detected, the unit will indicate it is full with a blue light bar flashing. You will also receive a notification on your phone if you use the Whisker App., Dec 10, 2021 · 1. Empty the Drawer. On the Litter-Robot, you have a drawer that collects the cat litter. If it becomes full, the blue light will blink rapidly. But if you throw out the mess, the lights should go off. Before returning the drawer to its compartment, remember to place a new liner into the container. , Hey all! I’ve had my Litter Robot 3 for over 5 years now, and have had some issues with it over the last couple of years. Litter robot did send me some new wiring which my husband installed, and while that mostly fixed the issue (the cycle button was flashing yellow constantly and as a result it never cycled) it now seems to have the same issue cropping up again. , 1. Empty the Drawer. On the Litter-Robot, you have a drawer that collects the cat litter. If it becomes full, the blue light will blink rapidly. But if you throw out the mess, the lights should go off. Before returning the drawer to its compartment, remember to place a new liner into the container., The unit is pushed into a corner, against a wall, or furniture. The red blinking light indicates CATS (the cat sensor) is detecting excess weight for more than 2 minutes. To test your changes, power the unit off and then on. Allow the unit to complete the start‐up cycle and return Home with a solid blue light., Out little robot has a continuous yellow /amber cycling light and the control panel is totally unresponsive. Things we have tried: Cleaning the pinch sensors Checking the spring sensor Powering off and on (via plug as power button not responsive) Checking for control panel lockout Checked back clips are in Checked globe is locked at the back., Tellingsenmd • 2 mo. ago. Easy fix for three solid green lights, and two flashing red, which is cat sensor fault. I just got off the phone with the litter robot experts. The three open circles at the top of the ring have the sensors behind them. and they are very sensitive to obstruction from cat hair or debris., If your litter robot 3 is not able to complete a cycle and is flashing yellow randomly, then watch this video for the fix!Our litter robot was giving us nigh..., If your Litter-Robot 3 is displaying a yellow light flashing quickly, this indicates a cycle has been interrupted by the Anti-Pinch Safety Feature and you will need to inspect the pinch sensor. Inspect the Sensors The purpose of the pinch sensor is to detect if an object is blocking the waste port during the Globe rotation., Mar 25, 2022 · To abort the clean cycle, press reset or empty. Press any button to put the unit on pause. On the other hand, a blinking yellow light signals a problem. How to resolve the issue depends on the flashing sequence: A slow yellow flashing light (one flash per second) , Cover the light sensor which is located under the power button. If the night light turns on and the cycle is interrupted, then your bonnet needs to be replaced. It is possible that the night-light is not even working, in this case, please remove the power from the robot and unclip the bonnet. Inside the bonnet you will see 2 wires connected to ..., Out little robot has a continuous yellow /amber cycling light and the control panel is totally unresponsive. Things we have tried: Cleaning the pinch sensors Checking the spring sensor Powering off and on (via plug as power button not responsive) Checking for control panel lockout Checked back clips are in Checked globe is locked at the back., Apple released a new “Dim Flashing Light” feature that can automatically dim flashing lights or strobe effects. Apple released the tvOS 16.4 update to the public yesterday, bringing various improvements to the system, including a new “Dim F..., I have owned my Litter Robot 3 for a little over a year and about a week ago it began to get stuck upside down when cycling. The litter box becomes unusable, and the wastebin is exposed. The yellow light is blinking. In order to fix it, I've been having to turn the unit off and back on. And even then, it will only work once before it gets stuck ..., In a desperate attempt to communicate with the LR4, I tried holding the power and connect button together. It made the light turn into 1 pink square, then 2 pink squares, and now it’s flashing pink and yellow while still being unresponsive. I can find no reference to this light code, other than a reddit comment from a litter robot ..., No, it often doesn’t cycle while not full yet. 3. Babypeapod22 • 1 yr. ago. Definitely take it apart and clean it and the sensors, it’s sensors are probably pretty dirty and can’t read a whole lot of it’s been a year without 😁. 1., When the Litter-Robot 3 Connect first arrived, we were shocked at the sheer size of the box. It was a box large enough for a kitchen table. The box is so large because the unit comes pre-assembled. All you have to do is hoist the 24-pound unit out of its shipping container, plug it in, and you’re ready to go., If you have a Litter-Robot III Open Air 3 and it's stopped working with yellow blinking / flashing light and/or the globe does not rotate in normal operating cycle or spinning continuously counter clockwise in one direction, then this video might be for you. , All three flashing simultaneously: This means the unit cannot find the Dump or Home position. Disassemble the Globe and flip the magnets at both the 1 o’clock and 5 o’clock position. Replace the Globe, making sure it is on straight and in its tracks. At the back of the Globe, turn the black Key into the Key Pocket., Litter-Robot Customer SupportPhone: 1-877-250-7729 | Hours: 9am - 7pm ETEmail: [email protected]. We have had our Bisque-colored (we just got a Grey LR III) Litter-Robot Open Air for 3 years. Here's the email that LR sent me that I reference in our "repair" video: If the Litter-Robot 3 cannot find the Dump and/or Home position ..., Disconnect the bonnet. Gently flex the two front bonnet tabs outward and hold for about 20-30 seconds. Reattach the bonnet. There are four tabs total: two in the back, two on the sides. You should feel a secure snap and hear a “click” when placed back into the slot, and the bonnet should sit closer to the base., Hey all! I’ve had my Litter Robot 3 for over 5 years now, and have had some issues with it over the last couple of years. Litter robot did send me some new wiring which my husband installed, and while that mostly fixed the issue (the cycle button was flashing yellow constantly and as a result it never cycled) it now seems to have the same issue cropping up again. , The Litter-Robot 3 is equipped with Cat Sensor that detects when a cat enters and exits the Globe. If the timing light is solid red, this indicates the Cat Sensor has been activated by a cat entering the Globe. ... If the cycling light is slowly flashing yellow (about once per second) or you are receiving a Cycle interrupted or Bonnet removed ..., Release to resume cycle. Button Functions Battery Backup Kit Battery nests in battery pocket in base of unit. Price: $39.95 (Free Shipping) Litter-Robot Premium Litter All Natural Sun-dried Clay. Non Tracking, 99% Dust Free. Price: $29.95 (Free Shipping) Drawer Liners (100 pk) Biodegradable bags for your Litter-Robot. Price: $39.99 (Free ..., I did :( it's just below the line. It finally ran a full cycle, randomly. Worried it won't run again after a cat uses it because of how it's acting. I put the other litter box out just in case it stops again. I've also checked the balance because we have it on a run, making sure the base is actually on the floor and not against the wall., Disconnect the bonnet. Gently flex the two front bonnet tabs outward and hold for about 20-30 seconds. Reattach the bonnet. There are four tabs total: two in the back, two on the sides. You should feel a secure snap and hear a “click” when placed back into the slot, and the bonnet should sit closer to the base. , The Litter-Robot will now perform an initial clean cycle. Need help? Visit whiskersupport.com Use clumping litter or litter beads and crystals that are small enough to pass through the screen. Add litter until it meets the raised MAX fill line when spread flat (8-10 lbs or 3.6-4.5 kg). Be careful not to overfill. Download the Whisker app and ..., But bending in the tabs on the bonnet for a tighter fit helped for a while, which might be worth a try. Check and see if the weight in the rubber liner is properly seated, if it is you should be able to feel it if you press up into the center of the liner while it's upside down. Mine was not and it caused my LR to constantly get stuck upside ..., To troubleshoot the blue blinking, let's start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged and unplug your power supply from the base 2.) Wait 10 seconds, then plug the unit back in. 3.) Allow the unit to complete a start-up cycle. If the light is solid blue, the code has been successfully ... , The following troubleshooting should resolve the blue light blinking while the waste drawer is empty. Once resolved, the unit should consistently recognize when your cat visits and cycle accordingly. To troubleshoot the blue blinking: Remove the drawer from the unit and press RESET. If the unit goes to solid blue, press the CYCLE button. The unit …, Conclusion. The blue light on your Litter Robot may be flashing for several reasons. The most common reason is that the unit is not receiving enough power. Check to make sure that the power cord is plugged into a working outlet. Other reasons the blue light may be flashing include a full waste drawer or a clogged motor., Litter Robot III - Flashing lights sequentially or flashing all at once. Most of you are here because there are 3 flashing lights on your Litter-Robot's control panel. Sometimes this problem is caused by a faulty power supply or the motor itself. If even after checking the set screw on the motor and checking the voltage on the power supply with ..., Title: 8.5x5.5 QRG 2016_WEB Created Date: 12/19/2016 10:37:50 AM