Acurite reset button

Reinstall the batteries in the outdoor sensor. Once the batteries are inserted you should see the red LED light blink approx. every 16 seconds on the front of the sensor. The red LED light should NOT stay on continuously. Reinstall batteries and/or power cord into the display unit then immediately press and hold the reset button again for 20 ...

Reset the display by pressing and holding the CLEAR RECORD / RESET button for 10 seconds, located in the battery compartment of the display. The date and time will need to be entered after a reset. Make sure that the AcuRite Iris® (5-in-1) sensor is connected to the display first. Verify the additional sensors are set to different A-B-C ...CLEAR RECORD / RESET Button: Press to : clear record currently being viewed. Press AND HOLD for full reset to factory defaults. 6. A-B-C Switch : ID code that must match 5-in-1 : sensor'sA-B-C switch to ensure: ... AcuRite sensors are sensitive to surrounding environmental conditions. ProperWait 1 minute to ensure that any remaining battery power has been discharged from both units. Reinstall batteries in the outdoor sensor (or sensors) first. Reinstall batteries in the …If the signal is not the issue, try following these steps to reset the display unit: Bring the outdoor sensor unit and the display unit close to each other. Remove the batteries from both units. Wait for at least 10 minutes to allow any residual power to drain from the units. Put the batteries back into both units.1. Backlight Button 5. Plug-in for Power Ada pter o r momentary bac light a nd d immer 6. Battery Compartment Cover settings. 2. Integrated Hang Holes 7. Power Ada pter PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE or easy wall mounting. 8. RESET Button WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS. 3.

After 20 seconds, go back to that prepared browser that has 192.168.4.1 typed in the URL and press enter. Once the AcuRite Wi-Fi display settings website (internal page) is open, select your Wi-Fi network's SSID from the dropdown (if you have a 2.4 GHz and a 5 GHz, be sure to select the 2.4 GHz), enter your Password, Station ID, and Station Key ...Clear out any false readings that were taken while you were cleaning your sensor by pressing the CLEAR TODAY button on your AcuRite Iris® (5-in-1) compatible display. ... Reset . If you are using a High Definition display unit such as model #06058M or #06088M, please use the following reset linked below: AcuRite Iris® (5-in-1) High Definition ...Reinstall the battery in the outdoor sensor. Reinstall the battery in the display unit. Let the units sit within a couple feet of each other for about 20 minutes to gain a strong connection. Relocate the display unit and/or the outdoor sensor. The units must be within 165 ft (50 m) of each other.Set the Time: Press and hold the "TIME" button for 5 seconds to begin the manual time set mode. The hour will flash on and off. Adjust the hour by pressing the "+" or "-" buttons (NOTE "PM"). Confirm and move on to the minute setting by pressing the "TIME" button. Adjust the minutes by pressing the "+" or "-" buttons.The red light near the AcuRite Atlas® (7-in-1) sensors battery compartment flashes every 10 seconds. If the AcuRite Atlas® (7-in-1) is still not registering rain on the display unit or you would like to clear any false rain data that registered when testing the sensor, please perform the hard reset steps below. Hard Reset:Make a pin hole in the bottom of a plastic cup. Hold the cup over the rain gauge and fill it with exactly 1 cup (8 oz.) of water, allowing the water to slowly drip into the rain gauge. You should hear the internal cups tipping and see the water drain through the rain gauge.

2 by pressing the "ALARM" button. Hold the "ALARM" button for 3 seconds. Press "+" or "-" to enter the desired alarm time and press "ALARM" to confirm the setting. Please be sure to note the PM indicator to ensure you have set the alarm for the proper time. To view alarm time 1 and 2, simply press the "ALARM" button to read ALARM 1 and ALARM 2. TheConnect the sensor and display unit and turn them off by removing all batteries and the power cord from each. Change the A-B-C switch on both devices to a …AcuRite Iris sensor and lightning sensor’s A-B-C switches to ensure units synchronize. 3. RESET Button Press and release for full reset to factory defaults. 4. Removable Tabletop Stand 5. Power Adapter 6. Battery Compartment Cover (not shown) 7. Plug-in for Power Adapter 8. LIGHT Button Dimmer control while using power adapter. Activates ...01099 Deluxe Wireless Weather Center with Barometric Pressure Charting. Follow. The information below applies to the following models: 01099, 01099C, 01099CDI, 01099CDIA1.

Hot light skins.

First, open your AcuRite Iris® (5-in-1) sensor by removing the (4) four screws from the bottom. The screws toward the center of the sensor are for Rain Gauge calibration only. Do not adjust these screws. After your sensor has been opened, remove any insects, cobwebs, or debris. An old toothbrush can help to clean out the hard-to-reach places.Watch on. The AcuRite Iris® (5-in-1) Weather Station collects outdoor temperature, humidity, wind speed, wind direction, and rainfall readings. The Dashboard will update data every 5 minutes and will include the last data packet received within the 5-minute interval. The details of the readings displayed are provided below.AcuRite Iris (5-in-1) Weather Station with Color Display and Weather Ticker. $149.99. Real-Time Weather Conditions: Receive readings for indoor outdoor temperature and humidity, wind speed/direction, barometric pressure, and rainfall. Large Color LCD Display with Adjustable Dimmer: Convenient to read and easily view data from various angles.RESET Button ; For full reset to factory defaults. 6. A-B-C Switch ; ID code that must match sensor's A-B-C switch to ensure units synchronize. 7. Power Adapter ... AcuRite atomic clocks use a radio-controlled signal (RCC) to synchronize to the correct time broadcast by the National Institute of Standards and Technology (NIST) Radio

Set the Time, Date & Units. Press and hold the "SET" button, located on the back of the clock, to enter SET MODE. Once in SET MODE the preference you are currently setting will blink on the clock. To adjust the currently selected (flashing) item, press and release the " " or " " buttons (press and HOLD to fast adjust).AcuRite 00754 User Manual View and Read online. Est. reading time 11 minutes. 00754 Thermometer manuals and instructions online. ... Reset display by pressing the RESET button, located on the back of the display unit inside the battery compartment. Date and time will need to be entered after a reset. Outdoor temperature is flashing or showing ...Bring the display and outdoor sensor units close to each other. Remove the batteries from the outdoor sensor unit and wait for 1 minute. Replace the batteries in the outdoor sensor unit. Press and hold the sync button on the outdoor sensor unit for 5 seconds until the LED light starts flashing. Press and hold the sync button on the display unit ...Jan 18, 2012 · http://www.AcuRite.com The AcuRite Digital Indoor / Outdoor Thermometer with Intelli-Time Clock & Calendar provides accurate, reliable temperature readings...All-time High and Low Records: All-time high and low records are the maximum/minimum data recorded since the unit was first powered on, since batteries were installed, or the unit was last reset. If the unit is the 00986 AcuRite Digital Fridge/Freezer Thermometer: The min/max records appear to the right of the current temperature reading from ...Cold temperatures can cause alkaline batteries to function improperly. Use lithium batteries in the sensor for temperatures below -4oF / -20oC. Slide off the battery compartment cover. Take note of the A-B-C switch setting inside the battery compartment . Insert 2 x AA batteries into the battery compartment, as shown.First, place the rain gauge on a level surface. Place the display close by so you can monitor it during calibration. Make a pin hole in the bottom of a plastic cup. Hold the cup over the rain gauge and fill it with exactly 1 cup (8 oz.) of water, allowing the …Alarms: To enter ALARM SET MODE, press and release the button. The currently selected setting will begin flashing on the display. To enable/disable the alarm for the currently selected (flashing) item, press and release the or arrow buttons. A icon indicates that the alarm is enabled. The alarm disabled icon looks like this .Set up your AcuRite Atlas ® Display 06104M / 06105M 1 INSTALL SENSOR BATTERIES • In the outdoor sensor battery compartment, locate the A-B-C switch. Be sure to note the channel that the A-B-C switch is set to.* • Install four AA alkaline or lithium batteries. Lithium batteries are recommended for temperatures below -4ºF (-20ºC).First, place the rain gauge on a level surface. Place the display close by so you can monitor it during calibration. Make a pin hole in the bottom of a plastic cup. Hold the cup over the rain gauge and fill it with exactly 1 cup (8 oz.) of water, allowing the water to slowly drip into the rain gauge.Take note of the A-B-C switch setting inside the battery compartment for part 2. 2. Insert 2 x AA batteries into the battery compartment, as shown. Follow the polarity (+/-) diagram in the battery compartment. 3. Replace the battery cover. 1 A-B-C Switch set to match display unit. 5. View and Download AcuRite 02038W instruction manual online.Place batteries in the main unit first. Lift off the rear cover of the remote sensor by separating front and back panels at the side seam. Place batteries in the sensor and press "TX" button to send a signal to the main unit. Select temperature display at this time by pressing the "C/ F" button. Replace back cover on sensor.

Before operating, plug the temperature probe into the thermometer. Press the " " button to turn the thermometer display ON. Press the " " " button on the thermometer display to enable " "or disable. " the audible alert. With the function enabled, the thermometer display will beep when Desired Temperature is reached.

Reset the Sensor. Locate the reset button inside the sensor’s battery compartment and press it to reset the sensor to its default settings. This can help resolve issues related to configuration errors or data corruption. After resetting, synchronize the sensor with the display unit to establish communication.Next, please make sure to perform the applicable reset before proceeding: AcuRite Iris® (5-in-1) Reset . If you are using a High Definition display unit such as model #06058M, #06088M, or #06102M please use the following reset linked below: AcuRite Iris® (5-in-1) High Definition Display Reset .Author Topic: New AcuRite Iris 5-in-1 will not connect to wifi (Read 1270 times) 0 Members and 1 Guest are viewing this topic. Atom. Member ... Not sure if your display has this, but on some displays there was a reset button in the battery compartment that you would press for 10 seconds to reset the display. This may be of some help:7. MIN Button Press to view today's low records. 8. , , & SET Buttons For setup preferences. 9. MAX Button Press to view today's high records. 10. Current Indoor Humidity 11. High Record Indicator Indicates today's high records are being viewed. 12. Display Low Battery Indicator 13. Date 14. Current Outdoor Humidity Arrow icon indicates the ...How to set a barometric pressure adjustment. From the Preferences section, select Calibrate Readings (+/-). From the Barometric Pressure setting, set a pressure adjustment in inches. Pressure can be adjusted up to ±10 inHg (338.6 hpa). Select the checkbox Calibrate Pressure. Select DONE to save your changes.Press the “ “ or “ “ buttons to select “STAND” for standard or “METRIC” for metric units. 4. Press the “ ” button to confirm your selection. 5. Next, you will see “WIND MPH”. Press the “ “ or “ “ buttons to select MPH, KPH, or KNOTS for wind speed units. 6. Press the “ ” button to confirm your selection.AND HOLD the " " button until the "SET" indicator appears in the area of the display labeled "ALARM" (left of the selected weather category) and thealarm setting flashes. 3. Adjust the alarm value by pressing the up or down arrow buttons. 4.Press the " " button to confirma value. 5.

Awnings for houses near me.

Yale forklift serial number year.

Pressing the button while viewing the main screen puts the display directly into Sleep Mode. Press any button to Wake. The display will automatically wake at the scheduled wake time. See Main Menu>Display Settings to set a Sleep/Wake schedule. While in Sleep Mode, the blue LED at the top of the display will pulse until the display is awakened.102021 www.acurite.com Quick Setup Guide 06099 VIEW HISTORICAL RECORDS • To view recent records on the display, press the records button, then use the buttons to navigate between yesterday and today, or clear the records if you wish.Summary of Contents for ACU-RITE 06058. ... Page 3 Features & Benefits Display Records BACK OF DISPLAY Button For setup preferences and cycling 1. Plug-in for Power Adapter through messages on the Weather Overview dashboard. ... OPERATION Using the Weather Station Menu Records Sensor Alarms Units Setup Calibrate Display Factory …To reset the AcuRite Iris High Definition Display, simply follow these steps: Unplug the power cord from the back of the monitor. Press and hold down the “Reset” button located on the rear panel of …Congratulations on your new AcuRite product. To ensure the best possible product performance, please read this manual in its entirety and retain it for future reference. ... First, locate the reset button inside the battery compartment of the display unit. Press and release this button to factory reset the weather station. Once it is reset ...This section is for general troubleshooting that applies to many devices. Atomic Clock Technology. Intelli-Time® Clock Technology. Inaccurate Barometric Pressure or Forecast. LCD Indoor Display and LED Clock Reset. High-Definition Indoor Display Reset. Set Time and Date on LCD Indoor Display. Select Degrees Fahrenheit or Celsius.Congratulations on your new AcuRite product. To ensure the best possible product performance, please read this manual in its entirety . and retain it for future reference. ... RESET Button . Full reset to factory defaults. 14. — Button . Decrease display brightness. 15. Battery Compartment 16. Plug-in for Power Adapter 17. USB Port 18 ...Unpacking Instructions. Remove the protective flm that is applied to the LCD screen prior to using this product. Locate the tab and peel off to remove. Package Contents. 1. Display unit 2. 3-in-1 sensor 3. Sensor mounting bracket 4. Mounting hardware Power adapter 6. Instruction Manual.Follow. The AcuRite Atlas® (7-in-1) Weather Station is designed for use in the Northern Hemisphere, however, it can be easily calibrated for use in the Southern Hemisphere. When using the AcuRite Atlas® (7-in-1) sensor in the Southern Hemisphere, the sensor will need to be mounted with the solar panels facing North and the wind vane will need ...AcuRite 02032. A weather center with various measuring tools to record local weather. ... If that doesn't work, try resetting the screen by pushing on the reset button found on the back of the display screen. Keep in mind, by doing this you will need to reset the date and time afterwards. Problems with the Temperature Fan.View and Download AcuRite 75107 instruction manual online. Weather Forecaster. 75107 weather station pdf manual download. Also for: 75077. ... UNIT 1. Integrated Hang Hole 6. SIGNAL Button For easy placement. Press to manually search for atomic signal. 2. SET Button 7. Fold-out Tabletop Stand For setup preferences. 3. "+" Button 8. Battery ... ….

After 30 minutes, press and release the " " button to re-activate the setup page. ** This weather station display only supports 2.4 GHz wireless networks 2. Power on the display (using included power cord).* 3. Connect to the Wi-Fi signal (named AcuRite 01516) of the AcuRite display from your computer or mobile device. 1.How to Reset Acurite Weather Station. If you’ve tried everything else on this list but your Acurite Weather Station is still giving you issues, then resetting it might help. First, locate the reset button inside the battery compartment of the display unit. Press and release this button to factory reset the weather station.Select “Remove A Sensor.”. If the display shows you a picture of the AcuRite Atlas sensor, Tap “Done” or “Yes” (If the screen does not change when you select Remove a Sensor, skip down to step 7). It may ask you to confirm removing the sensor. Select “Yes.”. The display will revert to the previous screen.2 by pressing the "ALARM" button. Hold the "ALARM" button for 3 seconds. Press "+" or "-" to enter the desired alarm time and press "ALARM" to confirm the setting. Please be sure to note the PM indicator to ensure you have set the alarm for the proper time. To view alarm time 1 and 2, simply press the "ALARM" button to read ALARM 1 and ALARM 2. TheThis product requires an AcuRite Notos ... RESET Button For full reset to factory defaults. 3. Backup Battery Compartment 4. Fold-out Tabletop Stand 5. Power Adapter 6. Plug-in for Power Adapter 7. A-B-C Switch ID code that must match sensor's A-B-C switch to ensure unitsSetup an Alarm. Press and release the color-coded button next to a location on the display for which you wish to set an alarm. Press and release the “ ((<'41))) ” button to enter alarm SET MODE. Press and release the “ ((('41))) ”, until the reading for which you wish to set an alarm is highlighted on the display.Cold temperatures can cause alkaline batteries to function improperly. Use lithium batteries in the sensor for temperatures below -4oF / -20oC. Slide off the battery compartment cover. Take note of the A-B-C switch setting inside the battery compartment . Insert 2 x AA batteries into the battery compartment, as shown.Manual: 00782W_instructions.pdf (1 MB) The information below applies to the following models: 00782W, 00782W2, 00782W3 Replaceable Parts: Replacement Sensor:...Congratulations on your new AcuRite product. To ensure the best possible product performance, please read this manual in its entirety . and retain it for future reference. ...The reset button is located within the battery compartment. Press and hold the button for a couple of seconds. After a reset, it will take around 4 hours for readings … Acurite reset button, AcuRite.com SAVE THIS MANUAL FOR FUTURE REFERENCE. to receive 1 year anty warr ection prt o Archive:l Products ... since it was manually reset (whichever was most recent). ... To manually reset the high/low records currently being viewed, press and HOLD the RECORDS button, located in the battery compartment for 3-5 seconds. 6 : temperature ..., The default temperature alarm settings for the freezer thermometer are minimum -20ºF / maximum 32ºF. 1. Select the sensor you want to customize by pressing the sensor’s blue button on the top of the display. 2. Press and release the “SET” button; the minimum temperature alarm setting will blink. 3., 3. Click the "Settings" button to specify the sensor you want to use for your weather forecasting data source and to select your geographic region. 4. Choose which sensor you want the forecast to use for temperature and humidity data. If you only have one sensor, only one will be listed. 5. Click to save settings., Bracket can be mounted on either side of thermometer. Bracket is flexible and can be formed to possition thermometer to your desired viewing angle. 3. Use 2 screws to mount bracket to side of thermometer. Start screws slowly. Some pressure is necessary to anchor screws in the plastic. 4. Use 2 screws to attach bracket to desired mounting surface., 13019: There is a reset pinhole on the back of the clock. With the clock plugged in, push a paper clip into this hole to hit the reset button. If the display turns back on showing “5 y n”, press and release the DST button once on the back and the time should display, allowing you to set it manually. If the display does not turn on or it ..., with Temperature & Humidity. Remove the Weather-Resistant Cover. Access the battery compartment by unscrewing the screws from weather-resistant cover. Remove cover. Be careful not to lose the screws or damage the cover during removal. 2 Set the Time. Turn the set knob on the back of the clock in either direction. 3 Install or Replace Batteries., Remove all power, AC adapter and batteries from the display unit. Press and hold down the reset button, located in the battery compartment, for 20 seconds. Plug back into AC power and insert recommended batteries. Press and hold down the reset button for an additional 20 seconds. Verify that the unit has powered on, and once a connection has ..., AcuRite customer support is committed to providing you with best-in-class service. For assistance, please have the model number of this product available and contact us in any of the following ways: (() (877) 221-1252. [email protected]. 24/7 support at www.AcuRite.com., Use the UP or DOWN arrows to navigate to or tap the Factory Reset option. You may receive a prompt asking if you want to reset to factory settings. Select "Yes". It may ask you, "Are you sure?", Select "Yes". The display will reset itself and go to the main AcuRite logo screen. You will now be able to set up the display by following the on ..., The AcuRite Atlas® (7-in-1) includes the capability to monitor temperature, humidity, wind speed and direction, rain, UV, and light intensity, plus the added protection of monitoring for lightning strikes (optional). The Dashboard will update data every 5 minutes and will include the last data packet received within the 5-minute interval., Press the release lever and pull off the lower housing of the sensor. Remove the battery compartment cover. Take note of the A-B-C switch setting inside the battery compartment. Insert 4 x AA batteries into the battery compartment, as shown. Follow the polarity (+/-) diagram in the battery compartment., First, place the rain gauge on a level surface. Place the display close by so you can monitor it during calibration. Make a pin hole in the bottom of a plastic cup. Hold the cup over the rain gauge and fill it with exactly 1 cup (8 oz.) of water, allowing the water to slowly drip into the rain gauge., To enter AUTO-CYCLE mode, press and release the “SELECT” button on the back of the display until the icon appears on the screen. Press and release again to exit AUTO-CYCLE mode. MANUAL: While in Manual Mode, press and release the “SELECT” button, located on the back of the display, to manually cycle through readings., In outdoor, low temperature conditions (below -4 degrees Fahrenheit / -20 degrees Celsius), AcuRite recommends NEW, HIGH QUALITY, NAME BRANDLITHIUM batteries for the best product performance. Verify batteries are fresh. The battery expiration date should be at least 5 years in the future. Batteries can lose 3% of their power or more every year ..., Use lithium batteries in the sensor for temperatures below -4oF / -20oC. Slide off the battery compartment cover. Take note of the A-B-C switch setting inside the battery compartment. Insert 2 x AA batteries into the battery compartment, as shown. Follow the polarity (+/-) diagram in the battery compartment., SENSOR. DISPLAY. Place the display in a dry area free of dirt and dust. Display. stands upright for tabletop use or is wall-mountable. To observe outdoor temperatures, the wired sensor must be. placed outside. The sensor can be securely mounted by using. the adhesive pad or the integrated hang hole., Locate the Time Zone Button imprinted on the back. ... Solution #6 Factory Reset the AcuRite Weather Station. If all else failed, you should perform a Factory Reset on the AcuRite Weather Station! It's one of the best methods to approach display problems with the station and in most cases, it manages to resolve the issue like a charm. ..., Page 4 Features & Benefits DISPLAY BACK Button 7. RESET Button Press to access all-time high and Full reset to factory defaults. low records. 8. Power Adapter Button 9. Plug-in for Power Adapter For setup preferences. 10. A-B-C Switch Button ID code that must match sensor’s A-B-C For setup preferences. Page 5: Setup, 1. Press and HOLD the " " button until the current temperature disappears and the maximum temperature alarm setting is shown in its place. 2. Press the " + " or " - " buttons to increase or decrease the maximum temperature alarm setting. 3. Press the " " button to confirm the maximum temperature alarm setting., Soft Reset. Hard Reset. AcuRite Weather Station Inaccurate Temperature Readings. AcuRite Weather Station Still Not Working. FAQ. How do you reset an …, Locate the A-B-C switch inside the battery compartment. Set. Insert 3 x AAA alkaline batteries into the battery compartment, as shown. Follow the A-B-C switch to A, B or C. You must select the same letter choices for both the display and 3. Replace the battery the sensor in order for the units to., Bring both the sensor and display indoors and remove at least one battery from each. Reinstall the battery in the outdoor sensor. Reinstall the battery in the display. Let the units sit within a couple feet of each other for a few minutes to gain a strong connection. Relocate the display and/or the outdoor sensor., Use the UP or DOWN arrows to navigate to or tap the Factory Reset option. You may receive a prompt asking if you want to reset to factory settings. Select "Yes". It may ask you, "Are you sure?", Select "Yes". The display will reset itself and go to the main AcuRite logo screen. You will now be able to set up the display by following the on ..., AcuRite Support. AcuRite product support is now offered exclusively through email and live chat. You can reach our U.S. based support staff by submitting a request or by chatting with our Live Agents during business hours. Agents are available for live chat Monday through Friday from 8:00 am to 4:30 pm CT, by clicking the Help button in the ..., Weather Alert Radio. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the. desktop model #08500/08505. receiver is connected. • Consult the dealer or an experienced radio/TV technician for help., Factory Reset Alarms Units Calibrate press to exit menu 1 5 2 6 3 7 4 8 Navigate to the main menu at any time by pressing the " " button. From the main menu, you can view records, set alarms, setup an additional sensor and more. 1. Records Access the "Records" sub-menu to view high and low values recorded for each location, Set the Time & Date. Choose the correct time zone (AST HST AKST PST MST CST EST) using the "TIME ZONE" switch on the bottom of the clock. Set Daylight Saving Time ON or OFF using the "DST ON/OFF" switch on the bottom of the clock.*. Press and hold the "TIME SET" button for 3 seconds to enter the SET MODE., Weather Alert Radio. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the. desktop model #08500/08505. receiver is connected. • Consult the dealer or an experienced radio/TV technician for help., Forgetting your account password can be a frustrating experience, but resetting your password doesn’t have to be difficult. Here are some easy steps to help you reset your account ..., Reset : Full reset to factory defaults. 8. A-B-C Switch : ... " button to enter SETUP MODE. Once in setup mode, the ... AcuRite's patented Self-Calibrating Forecasting provides your personal forecast of weather conditions for the next 12 to 24 hours by collecting data from, Selecting "Wi-Fi Setup" reactivates the Wi-Fi feature for an additional 30 minutes and displays step-by-step instructions on how to enable this feature. Add a New Sensor. To connect a new sensor or reconnect a sensor after a reset or battery change, select "Add a New Sensor" to allow the display to search for sensor signals. Remove a Sensor., 1. Press and HOLD the " " button until the current temperature disappears and the maximum temperature alarm setting is shown in its place. 2. Press the " + " or " - " buttons to increase or decrease the maximum temperature alarm setting. 3. Press the " " button to confirm the maximum temperature alarm setting., Set the Time & Date. Press and hold the “SET CLOCK” button, located on the side of the clock, to enter SET MODE. Once in SET MODE the preference you are currently setting will blink on the clock. To adjust the currently selected (flashing) item, press and release the “ ” or “ “ buttons (press and HOLD to fast adjust).