Hunter sprinkler adjustment instructions

Pop-up body for spray-irrigation systems. Fits most industry-standard female nozzles for versatile use. Highly durable, extra-thick body and cap for maximum performance. Covers up to 706 sq. ft. for optimal watering. Provides a spray distance of up to 15 ft. for use in many watering applications. Heavy-duty construction with an extra-thick body ...

Hunter sprinkler adjustment instructions. Factory setting is for full radius, and the radius can be reduced by 25%. With the MP Rotator tool (MPTOOL) or a small flat bladed screwdriver, rotate the Radius Adjustment Screw: -Clockwise (4 full turns) to decrease the radius. -Counter-clockwise (4 full turns) to increase the radius. Note: Radius reduction is intentionally limited by a slip ...

I-20. The I-20 is loaded with upgraded features such as FloStop® control, check valves, and efficient nozzles that make it the perfect choice in a range of applications. Radius 17' to 46'. Flow 0.36 to 14.8 GPM. Inlet Size ¾" NPT. Versatile: 34 nozzles and 6 body choices. Durable: Tough factory-installed rubber cover.

Open the Bleed Screw. The other way is to use the bleed screw the same way, loosen the screw enough to release air (1/4 to 1/2 turn). Hand tighten the screw to shut the valve off. NOTE: When using this method, you will …Insert the plastic end of the Hunter adjustment wrench into the FloStop adjustment socket. A rotation clockwise 90 degrees will stop the flow of water, a rotation counterclockwise will allow the flow of water. I-20 Installation Card Select Language I-20 Rotary Sprinkler Adjustment InstructionsNote: It is not necessary to disassemble the sprinkler to make adjustments. ® Institutional Series™ I-10 & I-20 Ultra Gear-Driven Sprinklers ARC ADJUSTMENT The I-20 Ultra pop-up sprinkler should be installed at finished grade as shown in the illustration (Fig. 1). To Increase the Arc: 1. Insert the plastic key end of the Hunter wrench into ...Insert the key end of the Hunter wrench into the adjustment socket on top of the sprinkler. While holding the nozzle turret at the right stop, turn the wrench clockwise. (Note: all adjustments can be made with less than one full turn of the adjusting wrench.) The wrench will stop turning when adjusted to the maximum arc (360°).X-Core Support. Welcome to the X-Core irrigation controller support section. The X-Core, which is the XC timer predecessor, is Hunter’s professional controller for 2 to 8 zones. This section will show you how to install, program and troubleshoot your X-Core controller.Adjusting the arc and radius of a rotor is an easy task. Most residential rotors are adjusted the same way. There are two adjustments that can be made on rotors, arc and radius. Arc: The degrees of coverage of a sprinkler from one side of pattern to the other. A 90-degree arc would be a quarter-circle sprinkler.The nozzle turret must be held in this position for all arc adjustments. To increase arc: 1. Insert the key end of the Hunter wrench into the adjustment socket ...Can work in tandem with larger rotors to combine big and small areas in a single zone. 1,963 sq. ft. of coverage for optimal watering. 4 in. pop-up clears the turf. 40 - 360 degree arc provides adjustment from the top of the sprinkler when wet and dry. Radius-adjustment screw for positive nozzle retention and fine-tuning of the spray.

Dig out a 1- to 2-inch ring around the sprinkler carefully so you don’t hit the waterline. Remove both dirt and sod and unscrew the sprinkler head using a counterclockwise motion. Screw on the new head by threading it on the stem snugly, but don’t crank it down. Fill the original dirt and sod back in around the head.With a rotor tool, its easy to adjust the left stop, but ever wonder how to adjust the right stop after install? Mike from Hunter technical support will show...Flow adjustment and servicing made easy Flow management is a simple process when using the Hunter PGV with its non-rising fl ow control handle in the 1½" and 2" sizes. A non-rising handle means the valve can be placed closer to the valve box lid for easier servicing. When fi ne tuning the system, adjust to the desired zone fl ow either by hand 1. Insert the plastic key end of the Hunter wrench into the adjustment socket. (Fig. 3 & 4). 2. While holding the nozzle turret at the right stop, turn the wrench counter-. clockwise. Each full 360° turn of the wrench will decrease the arc 90°. 3. Adjust to any arc between 50° and 360° (Fig. 5).Increasing the Arc. Insert the plastic end of the Hunter adjustment wrench into the arc adjustment socket. While holding the nozzle turret at the right stop, turn the wrench clockwise. Each full 360 degree rotation of the wrench will increase the arc 90 degrees. You can adjust the arc anywhere in between 50 degrees and 360 degrees.

Hunter Pro-Spray Sprinkler Bodies are engineered to ensure long-lasting, reliable performance. Available in heights from shrub to 12”, Pro-Spray heads feature durable construction that is second to none, exclusive body cap design that doesn't leak even when loosened, and a reliable, easy-to-adjust two-piece ratchet. Insert the key end of the Hunter wrench into the adjustment socket. While holding the nozzle turret at the right stop, turn the wrench counterclockwise. Each full 360º turn of the wrench will decrease the arc 45º. Adjust to any arc between 40º and 360º. The wrench will stop turning, or there will be a ratcheting noise, when the minimum arc ...In this video I show you how to make adjustments to your Hunter sprinkler heads including, left and right stops, water pressure, and spray nozzle. You'll ne...Instagram | https://www.instagram.com/old_car_alley/Had to replace one of the sprinkler heads in dad's yard a couple weeks ago, so I did a very …2 Pack Hunter MP Rotator Adjustment Tool MPTOOL, Orange Sprinkler Adjustment Tool, Hunter MPTool Sprinkler Tool Pack of 2 Adjustment Wrench for all MP Rotator Nozzles with Included LED Keychain Light. ... Hunter/Orbit Gear Drive Tool, ROTORTOOL, MP Rotator Tool, Hold Up Collar, USB Flash Drive w Instructions. 4.6 out of 5 stars 51. …

Relias learning test answers.

The sprinklers come from the factory with a preset spray arc of 1º (a very thin stream). The raised dot on top of the nozzle indicates the adjustable (left) edge of the spray pattern. With the raised dot aligned to the right-hand border of the coverage area, insert the Hunter wrench into the stainless-steel hex screw and turn the screw counter ...ARC ADJUSTMENT INSTRUCTIONS The sprinkler can be adjusted to any arc setting between 40˚ and 360˚. This can be done while the ... Hunter Industries Incorporated • 1940 Diamond Street • San Marcos, California 92069 • Tel: 1-760-744-5240 • Fax: 1-760-471-9626. Title: GLIT-0151. Insert the key end of the Hunter wrench into the adjustment socket on top of the sprinkler. 2. While holding the nozzle turret at the right stop, turn the wrench clockwise. 3.The photo shows the adjustment method without the sprinkler installed. ... 1/2" and 3/4" Hunter Check Valve Product Installation and Adjustment. Title: 23-561.web Author: Hunter Industries Subject: HCV Installation and Adjustment Instructions Created …

Category. This video explains how to adjust and maintain Hunter sprays on an irrigation system. Mike, a Hunter Technical Support Representative, demonstrates flushing a spray sprinkler upon installation, adjusting the arc, adjusting the …Place the tool's notched edge under a cap's lip, and pry the cap upward. After removing a sprinkler head's cap, pull out the black, click-set disk in the center of the sprinkler head, flip the disk to the gray side and push it back in place in the sprinkler head, if you want to redirect the spray pattern from a full circle to partial.Download Adobe Reader here. Owner's Manuals and Instruction Sheets Easy-to-understand owner's manuals and instruction sheets make installing and programming Hunter products a simple task. Our manuals contain clear illustrations, easy to read fonts, and are written by the engineers and product managers that brought the products to life. Unscrew the body cap and remove the internal assembly. Place the base of the riser on a solid surface and grip the spring and riser body firmly. With your other hand, snap off the body cap. With your palm on top of the logo cap, pull up with your fingers. While still gripping the spring and body, remove the rubber seal.Insert the plastic end of the Hunter Key into the adjustment socket. 2. While holding the nozzle turret at the right stop, turn the key clockwise. Each full 360° turn of the key will increase the arc 90°. 3. Adjust to any arc between 40° and 360°. 4.The key will stop turning, or there will be a ratcheting noise, when the maximum arc of 360 ...MP Rotator - Adjusting the Radius and Arc. Install the MP Rotator with the Left Edge Indicator pointing to the left side of the desired watering pattern. With the MP Rotator operating and in the pop-up position, rotate the Arc Adjustment Ring. Turning the Arc Adjustment Ring clockwise will increase the arc, counter clockwise will decrease the arc.May 30, 2021 · This is a quick video explaining how to adjust the Hunter PGP Rotor Head. The right/left adjustments and the Arc adjustment. sprinkler system for repairs or winterizing without shutting off the water to the entire house. It is rec-ommended that all systems be equipped with a shutoff valve installed in a box for easy access. Some systems also require the use of a back-flow preventer. Check local building codes. The second type of valve is the sprinkler "zone valve."

Unscrew the body cap and remove the internal assembly. Place the base of the riser on a solid surface and grip the spring and riser body firmly. With your other hand, snap off the body cap. With your palm on top of the logo cap, pull up with your fingers. While still gripping the spring and body, remove the rubber seal.

Seasonal Adjustment Allows user to make run time changes according to the seasons without reprogramming the controller. Bars on the left allow quick visual reference to the seasonal adjustment percentage. 1 Manual-One Station Allows user to activate a one-time watering of a single valve System Off Allows user to discontinue all programs and ...condition. These instructions cover initial arc setup and adjustment while the rotor is in the static off condition and with the riser installed in the rotor. ② Pull up the riser assembly using the Hunter Wrench or T-Handle Tool. While holding the riser in the raised position, snap the G85 Arc-Adjustment/ Hold-Up Tool onto the arc adjustment ringSimple video instructions on how to adjust the arc and radius of the Huter PGP Sprinkler. Most residential sprinklers are adjusted in the same way.Jun 20, 2013 · With a rotor tool, its easy to adjust the left stop, but ever wonder how to adjust the right stop after install? Mike from Hunter technical support will show... sprinkler to realign the right arc. PGP ULTRA INSTALLATION: The PGP Ultra pop-up sprinkler should be installed at finished grade as shown in the illustration (Fig. 1). Arc Adjustments: Adjustable heads are preset to approximately 180˚. Sprinklers may be adjusted with water on or off. It is recommended that initial adjustments beTurf Industries has been installing irrigation systems and landscape lighting in Chicagoland since 1982. Every irrigation & landscape lighting system is prof... You can adjust which spray of your sprinklers to keep your lawn happy and healthy. Sprays what a convenient way to maintaining a lush lawn or irrigate a garden. …This video explains how to adjust a Hunter PGP gear drive rotor up close. We are a sprinkler repair and installation contractor. American Irrigation Repair ...Insert the plastic key end of the Hunter wrench into the lifting socket of the sprinkler and turn 90°. Pull the riser up to gain access to the nozzle socket (Fig. 8). 2. Using the hex …

How to find friends in 3008 roblox.

White round pill with 54 27 on it.

Method 1 Radius Adjustment Download Article The radius is the distance from the sprinkler head to the edge of the water spray. It comes preset to your sprinkler nozzle's maximum distance, and you can reduce it by up to 25%. [1] 1 Insert the hex end of your Hunter wrench key into the radius reduction screw.Insert the plastic key end of the Hunter wrench into the adjustment socket (Fig 3 & 4). While holding the nozzle turret at the right stop, turn the wrench ...adjustments. The right stop does not change. to Increase the arc: 1. Insert the plastic key end of the Hunter wrench into the adjustment socket (Fig. 3 & 4). 2. While holding the nozzle turret at the right stop, turn the wrench clockwise. Each full 360˚ turn of the wrench will increase the arc 90˚. 3. Adjust to any arc between 40˚ and 360 ...Factory setting is for full radius, and the radius can be reduced by 25%. With the MP Rotator tool (MPTOOL) or a small flat bladed screwdriver, rotate the RADIUS ADJUSTMENT SCREW: Clockwise (4 full turns) to decrease the radius. Counter-clockwise (4 full turns) to increase the radius. Note: Radius reduction is intentionally limited by a slip ...The radius, or distance the water sprays on Hunter Nozzles can be adjusted by turning the center screw on top of the nozzle. This will increase or decrease the radius. All nozzles come from the factory in the fully open position (fully counterclockwise position). 1. Ensure that the nozzle is fully screwed down onto the pop up or shrub body ...Note: It is not necessary to disassemble the sprinkler to make adjustments. ® Institutional Series™ I-10 & I-20 Ultra Gear-Driven Sprinklers ARC ADJUSTMENT The I-20 Ultra pop-up sprinkler should be installed at finished grade as shown in the illustration (Fig. 1). To Increase the Arc: 1. Insert the plastic key end of the Hunter wrench into ...Increase the Arc Insert the plastic key end of the Hunter wrench into the adjustment socket . While holding the nozzle turret at the right stop, turn the wrench clockwise. Each full 360° turn of the wrench will increase the arc 90°. Adjust to any arc between 40° and 360°.The Hunter adjustment wrench consists of a 3/32 allen key ; The Hunter Rotor adjustment tool is used to make arc and radius adjustments ; ... PGP Ultra and I20 Ultra Rotor Sprinkler Heads, Hunter 782900 Nozzle Rack Set, Includes LED Keychain Light. 4.4 out of 5 stars ...Hunter PGP Sprinkler, PGP Rotary Sprinklers Adjustment Instructions View mosupport documents. Hunter Technical Support experts aavailable to answer your question(s) about HunterTo Increase The Arc: Insert the key into the arc adjustment slot, indicated by an arrow in the center of the turret. Hold the turret in place while turning the tool clockwise. Keep turning until the arrow points to the desired arc. The arrow will point to the adjustable right stop. Note: When the rotor is set at 360°, it will continuously ...per the programming instructions in the Owner’s Manual provided with your controller. The Solar Sync receives data from the sensor and applies it daily to the controller’s water schedule by adjusting the controller’s programmed irrigation run times through the Seasonal Adjustment feature in the controller. Wired Solar Sync Wireless Solar Sync Hold the plastic nozzle stationary by inserting the two pins on the side of a Hunter wrench between any of the nozzle spokes. With a second Hunter wrench, turn the stainless-steel hex screw clockwise to decrease, and counter-clockwise to increase the radius and discharge rate. The radius should not be reduced more than 25%. (The sprinkler is ... ….

Watch on Arc Adjustment Adjustable heads are preset to approximately 180 degrees. The PGP-ADJ is adjustable from 40-360 degrees. The PGP Ultra is adjustable from 50-360 degrees. Sprinklers may be adjusted with water on or off. It is recommended that initial adjustments be made before installation.Increasing the Arc. Insert the plastic end of the Hunter adjustment wrench into the arc adjustment socket. While holding the nozzle turret at the right stop, turn the wrench clockwise. Each full 360 degree rotation of the wrench will increase the arc 90 degrees. You can adjust the arc anywhere in between 50 degrees and 360 degrees.This video explains how to adjust a Hunter PGP gear drive rotor up close. We are a sprinkler repair and installation contractor. American Irrigation Repair ...sprinkler system for repairs or winterizing without shutting off the water to the entire house. It is rec-ommended that all systems be equipped with a shutoff valve installed in a box for easy access. Some systems also require the use of a back-flow preventer. Check local building codes. The second type of valve is the sprinkler "zone valve."They ability alter aforementioned spray of your sprinklers up hold your lawn happy and healthy. Sprinklers are a convenient way to maintain a lush lawn or irrigate a gardens. However, they only work supposing they effectively water your property! We're driving to...To adjust the current time on your Hunter sprinkler system controller, turn the dial to "Current Time/Day. " This will cause the displayed numbers to start flashing. Then, use the plus and minus buttons on the device to change the numbers accordingly. When you're ready to move on to minutes, date, and year, you can use the left and right ...Hold the plastic nozzle stationary by inserting the two pins on the side of a Hunter wrench between any of the nozzle spokes. With a second Hunter wrench, turn the stainless-steel hex screw clockwise to decrease, and counter-clockwise to increase the radius and discharge rate. The radius should not be reduced more than 25%. (The sprinkler is ...Hunter’s revolutionary MP Rotator® Nozzles use multi-stream technology to deliver accurate streams of water with superior uniformity. When used in place of standard spray nozzles, it’s not uncommon to see system water use decrease by 30% or more. This technology and water savings is brought to life in the Pro-Spray PRS40. How to adjust and maintain Hunter sprays on an irrigation system. Adjusting the arc, adjusting the radius, cleaning the filter and installing a check valve. Hunter sprinkler adjustment instructions, Features a flat-blade screwdriver and lifting tool in one. The Rain Bird Gear Sprinkler Adjustment Wrench is used to adjust the throw of the 3504, 5004, 6504 ..., Field Knowledge. Download MOV. Download WMV. Learn how to adjust water flow directly at the valve using the Flow Control adjustment feature. You can increase or decrease the flow of water for optimal water use. This is a great water conservation feature available as a built-in option on many Hunter valves., 1. Insert the key end of the Hunter wrench into the adjustment socket on top of the sprinkler. 2. While holding the nozzle turret at the right stop, turn the wrench clockwise. 3., Learn how to adjust a Hunter PGP rotary sprinkler head. The process is similar for the I series models and the PGJ.Product Info:https://www.ewingoutdoorsuppl..., This video explains how to adjust and maintain Hunter sprays on an irrigation system. Mike, a Hunter Technical Support Representative, demonstrates flushing ..., The nozzle turret must be held in this position for all arc adjustments. To increase arc: 1. Insert the key end of the Hunter wrench into the adjustment socket ..., Turn the nozzle adjustment screw clockwise to reduce the radius or counterclockwise to increase the radius. Four full rotations will maximize the effect. Additional rotations will not affect the performance of the nozzle. ③ Arc Setting The MP Rotator has a fixed left edge on all 90°–210° models and 210°–270° models. Turn the ..., sprinkler system for repairs or winterizing without shutting off the water to the entire house. It is rec-ommended that all systems be equipped with a shutoff valve installed in a box for easy access. Some systems also require the use of a back-flow preventer. Check local building codes. The second type of valve is the sprinkler "zone valve.", Residential Rotors - I-20 Rotary Sprinkler Adjustment Instructions Aligning the Right Fixed Side of Arc The right side of the arc can be realigned to avoid wet walkways or a dry turf area. One way to realign the right stop is to turn the whole sprinkler body assembly and the fitting below., Irrigation Notes: Reduced Sprinkler Radius Professional Turf Manager's Guide to Efficient Irrigation Practices and Equipment Sprinkler Replacement Charts - Institutional Series Rotary Sprinklers, Our manuals contain clear illustrations, easy to read fonts, and are written by the engineers and product managers that brought the products to life. View Owner's Manuals by product and category View all Controller Owner's Manuals X-Core | PCC | Pro-C | I-Core | Dual | ICD-HP | XC Hybrid | NODE | WVP/WVC View all Sensor Owner's Manuals, Residential irrigation controller (230 pages) Controller Hunter X-Core Owners Manual And Programming Instructions. Residential irrigation controller (31 pages) Controller Hunter SRC Instructions. (3 pages) Hunter X-CORE Quick Start Manual. (article) Irrigation System Hunter XC Hybrid Quick Start Manual., To Increase the Arc: 1. Insert the plastic key end of the Hunter wrench into the adjustment socket (Fig. 3 & 4). 2. While holding the nozzle turret at the ..., The PGP Gear-Drive Rotor Sprinkler with 3-Gallon Per Minute Nozzle features an adjustable 40 - 360 degree arc for versatile coverage. The rotary sprinkler provides water-saving efficiency and uniform water distribution for consistent results. See details Hunter Pop-Up, Rotary PGP-ADJ Gear Driven Adjustable Sprinkler, 3 Gallons/Min., PGP ® Ultra. The PGP Ultra raises the bar for rotor technology with powerful features developed over three decades of research, customer feedback, and lab testing. Radius 17' to 46'. Flow 0.36 to 14.8 GPM. Inlet Size ¾" NPT. Automatic arc return: Returns to the original arc regardless of where the turret is turned. , Note: It is not necessary to disassemble the sprinkler to make adjustments. ® Institutional Series™ I-10 & I-20 Ultra Gear-Driven Sprinklers ARC ADJUSTMENT The I-20 Ultra pop-up sprinkler should be installed at finished grade as shown in the illustration (Fig. 1). To Increase the Arc: 1. Insert the plastic key end of the Hunter wrench into ..., Aug 13, 2021 · To adjust the current time on your Hunter sprinkler system controller, turn the dial to “Current Time/Day. ” This will cause the displayed numbers to start flashing. Then, use the plus and minus buttons on the device to change the numbers accordingly. When you’re ready to move on to minutes, date, and year, you can use the left and right ... , Rotate the nozzle turret to the right stop, screw the internal assembly back into the body with the nozzle aligned to the desired irrigation area and adjust the left arc as needed. Note: It is not necessary to dig up and remove the whole sprinkler to realign the right arc. The right stop position on the Hunter PGP can be easily adjusted., The Hunter adjustment wrench consists of a 3/32 allen key ; The Hunter Rotor adjustment tool is used to make arc and radius adjustments ; ... PGP Ultra and I20 Ultra Rotor Sprinkler Heads, Hunter 782900 Nozzle Rack Set, Includes LED Keychain Light. 4.4 out of 5 stars ..., Find tips on installation, nozzle adjustment, controller programming and more., I-20 Product Lines Rotors Category Field Knowledge Download MOV Download WMV Adjusting the arc and radius of a rotor is an easy task. Most residential rotors are adjusted the same way. There are two adjustments that can be made on rotors, arc and radius. Arc: The degrees of coverage of a sprinkler from one side of pattern to the other., Adjust to any arc between 40°-360°. To Decrease arc: Insert the key end of the Hunter wrench into the adjustment socket. While holding the nozzle turret at the right stop, turn the wrench counterclockwise. The wrench will stop turning when adjusted to the maximum arc (360°). Do not go past this stop. Adjust to any arc between 40° and 360°., Method 1 Radius Adjustment Download Article The radius is the distance from the sprinkler head to the edge of the water spray. It comes preset to your sprinkler nozzle's maximum distance, and you can reduce it by up to 25%. [1] 1 Insert the hex end of your Hunter wrench key into the radius reduction screw., must first determine the correct Sprinkler System Design Capacity — how much water is available for residential irrigation. If the system will be installed using city water, follow the steps below. If the water will be drawn from a lake or well, your Hunter dealer or the pump installer will have the specifications for pressure and volume. 1., Hunter’s revolutionary MP Rotator® Nozzles use multi-stream technology to deliver accurate streams of water with superior uniformity. When used in place of standard spray nozzles, it’s not uncommon to see system water use decrease by 30% or more. This technology and water savings is brought to life in the Pro-Spray PRS40. This efficient …, Residential irrigation controller (230 pages) Controller Hunter X-Core Owners Manual And Programming Instructions. Residential irrigation controller (31 pages) Controller Hunter SRC Instructions. (3 pages) Hunter X-CORE Quick Start Manual. (article) Irrigation System Hunter XC Hybrid Quick Start Manual., Great tool while it lasts. My Hunter PGP sprinkler heads are several years old so the pattern adjustment isn't easy like it is on a brand new unit. I got to the fourth sprinkler head and the plastic part broke. This tool would be fantastic if the pattern tool part was metal like the spray tool part. It only cost $0.67 so I can't be to upset., Residential irrigation controller (18 pages) Controller Hunter ACC-1200 Manual. Advanced commercial controller (100 pages) Controller Hunter X2-400 Quick Programming Manual. (2 pages) Controller Hunter Eco-Logic 6 Owners Manual And Programming Instructions. Station indoor controller (2 pages) Controller Hunter ICC2 Owner's Manual., An economical, mid-range gear-driven sprinkler for residential and commercial sites (16 pages) Irrigation System Hunter PGP Ultra Series Manual. Gear-driven sprinklers (2 pages) Irrigation System Hunter SRC Plus 600i Owner's Manual. Residential/light commercial irrigation controller, 6/9-station indoor international (32 pages), Seasonal Adjustment Allows user to make run time changes according to the seasons without reprogramming the controller. Bars on the left allow quick visual reference to the seasonal adjustment percentage. 1 Manual-One Station Allows user to activate a one-time watering of a single valve System Off Allows user to discontinue all programs and ..., Nov 1, 2017 · Pop-up body for spray-irrigation systems. Fits most industry-standard female nozzles for versatile use. Highly durable, extra-thick body and cap for maximum performance. Covers up to 706 sq. ft. for optimal watering. Provides a spray distance of up to 15 ft. for use in many watering applications. Heavy-duty construction with an extra-thick body ... , 2. Set the Right Position. On top of the rotor head, you should see a rubber cover with two to three access points. The point on the opposite side of the nozzle is where you can adjust how far your sprinkler head turns to the right. Place a rotor adjustment tool or a flathead screwdriver into the access point., Maybe you installed the MP Rotator yourself or we did it! Either way they need to be adjusted periodically. Here is a quick overview of how to dial in the MP...